|
04-11-2024, 12:43 AM | #1 |
VIP Member
Join Date: Oct 2007
Posts: 1,152
Likes: 452
Liked 322 Times in 118 Posts
|
On a low HP engine
should you have the block align honed?
|
04-11-2024, 06:36 AM | #2 |
VIP Member
Join Date: Nov 2002
Location: Massapequa Park,NY
Posts: 1,238
Likes: 1,793
Liked 889 Times in 281 Posts
|
Re: On a low HP engine
Is the block housing bores straight and the correct size ?
__________________
1989 Camaro Iroc-Z I/SA B&B Auto Machine Shop. |
Liked |
04-11-2024, 07:30 AM | #3 |
VIP Member
Join Date: Oct 2007
Posts: 1,152
Likes: 452
Liked 322 Times in 118 Posts
|
Re: On a low HP engine
|
04-11-2024, 08:53 AM | #4 |
VIP Member
Join Date: Oct 2002
Location: On a hilltop in Pa.
Posts: 4,332
Likes: 3,340
Liked 7,204 Times in 1,612 Posts
|
Re: On a low HP engine
Did you take the block apart? How did the bearings look? The crank? Did the crank spin free in the block?
__________________
Billy Nees 1188 STK, SS I'm OK..........it's everybody else. |
04-11-2024, 11:44 AM | #6 |
VIP Member
Join Date: Oct 2007
Posts: 1,152
Likes: 452
Liked 322 Times in 118 Posts
|
Re: On a low HP engine
|
04-11-2024, 03:00 PM | #7 |
VIP Member
Join Date: Dec 2001
Location: Texarkana Ark/TX
Posts: 2,399
Likes: 494
Liked 724 Times in 280 Posts
|
Re: On a low HP engine
I've seen too many variabes in factory mass production machining to say No.
I got to where I just lightly trimmed (.001-.002) the caps and dusted the main bores with the align hone on ever engine I built. It was amazing what I ran into. If it is a SBS or BBC be sure to install the oil pump. When it is torqued it affects the rear main bore.
__________________
Adger Smith (Former SS) |
Liked |
04-11-2024, 04:07 PM | #8 |
VIP Member
Join Date: Mar 2007
Posts: 2,354
Likes: 558
Liked 1,702 Times in 520 Posts
|
Re: On a low HP engine
I would have the machine shop check the main bore sizes with a dial bore gauge and straight edge to see if the block is straight and true. Somehow hen the block is line honed it causes timing chain fitment issues. You can get undersized sets to compensate for that but can be a pain. In all my years of racing I have only had one block line honed. That was after I broke a crankshaft. That block was never right after that. Ended up scrapping it.
__________________
Mike Pearson 2485 SS |
04-11-2024, 05:28 PM | #9 | |
VIP Member
Join Date: Oct 2007
Posts: 1,152
Likes: 452
Liked 322 Times in 118 Posts
|
Re: On a low HP engine
Quote:
would that be true for a small block mopar? |
|
04-12-2024, 07:49 AM | #10 | |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,444
Likes: 1,745
Liked 10,051 Times in 2,085 Posts
|
Re: On a low HP engine
Quote:
Thanks. |
|
Liked |
|
|