|
04-22-2020, 10:24 AM | #11 |
VIP Member
Join Date: Oct 2008
Location: Somerset,Ky
Posts: 1,305
Likes: 201
Liked 118 Times in 50 Posts
|
Re: T10 4 speed question
if it has Liberty pro-shift rings they will have welds holding them...if factory with every other tooth cut off there wont be welds and will still have the cone/taper area for synchronizer....
Another option if it is pro shifted w/liberty rings, Liberty's will face plate them now... Liberty's pro shift rings the lugs were 1/8' wide X 1/2'' ish long and usually have Liberty's stamped in them Doug Nash's were about 1/4''wide and 1/2'' long |
Liked |
02-21-2021, 04:21 PM | #12 |
Junior Member
Join Date: Feb 2021
Posts: 4
Likes: 0
Liked 1 Time in 1 Post
|
Re: T10 4 speed question
I have one of those T-10's, Joe at Liberty Gearsmade them, 2.99 first gear, 1.75,1.33,1.00 made from 9310 nickel steel, great box, it's worth rebuilding, but I'd rather find a 2.64 box for street and save the Liberty set for racing.
|
02-21-2021, 05:02 PM | #13 |
VIP Member
Join Date: Dec 2001
Location: phoenix
Posts: 1,455
Likes: 58
Liked 691 Times in 274 Posts
|
Re: T10 4 speed question
All gears can be bought on ebay. If the pro shifted gears have life left in them I would be interested in buying them. I dont have any extra gears to sell.
|
02-24-2021, 03:43 AM | #14 |
VIP Member
Join Date: Dec 2001
Location: Texarkana Ark/TX
Posts: 2,399
Likes: 496
Liked 724 Times in 280 Posts
|
Re: T10 4 speed question
A picture of what you have is worth 1,000 words. I might have some of what you need.
__________________
Adger Smith (Former SS) |
02-25-2021, 10:55 AM | #15 |
Senior Member
Join Date: Sep 2007
Location: Henderson, NV
Posts: 578
Likes: 7
Liked 47 Times in 25 Posts
|
Re: T10 4 speed question
I have an AS10T10Y sitting in the corner, bought in 1978. It has full synchros, nodular iron main case, aluminum tail, 26 spline input, 32 spline (Turbo 400) output, 2.88 first with 9310 gears. Back then, this was the "ultimate" in factory offerings on the aftermarket. Decoding the name, AS10 was the 9310 geared version, Y was the 2.88 first.
|
02-25-2021, 04:14 PM | #16 |
Junior Member
Join Date: Jul 2014
Posts: 48
Likes: 259
Liked 19 Times in 9 Posts
|
Re: T10 4 speed question
Curious,
I understood back in the day that the mid plate needed to be made of a material other than aluminum. So I'm sure the iron case is important and the tail housing can be aluminum, but what of the mid plate? Loren |
02-25-2021, 10:39 PM | #17 |
VIP Member
Join Date: Dec 2001
Location: phoenix
Posts: 1,455
Likes: 58
Liked 691 Times in 274 Posts
|
Re: T10 4 speed question
Steel mid plate helped alot over aluminum. Steel is a little harder to find.
|
02-25-2021, 10:47 PM | #18 |
Member
Join Date: Jun 2007
Location: St. Augustine, Fla.
Posts: 228
Likes: 511
Liked 39 Times in 9 Posts
|
Re: T10 4 speed question
Wade Transmission & Gear in Dallas. Texas will have what ever you need for the Borg Warner.
__________________
Reggie Winkles 2650/Stock |
Liked |
02-26-2021, 10:16 AM | #19 |
Senior Member
Join Date: Sep 2007
Location: Henderson, NV
Posts: 578
Likes: 7
Liked 47 Times in 25 Posts
|
Re: T10 4 speed question
Yes, the hollow (around the bearing) cast aluminum midplate was the weak point. I got the G&G iron midplate for mine.
|
|
|