|
![]() |
#11 |
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,999
Likes: 64
Liked 773 Times in 192 Posts
|
![]()
Caution on using anyone's fixtures. I bought a BHJ for a BBC years ago and after getting blueprints from Chev, found that the BHJ was out as much as most blocks. Then you have to wrestle with the assumption that the factory design and specs are the most optimum for valve train geometry. At least you will get them consistent.
__________________
![]() |
![]() |
![]() |
![]() |
#12 | |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
![]() Quote:
This was not brought up in the roller cam thread but it is a big reason why some guys are chewing thru lots of valvetrain parts..... did somebody mention.... "lifters"
__________________
__________________ Bill Diehl B200 C/D STK Last edited by Bill Diehl; 02-02-2016 at 07:08 PM. |
|
![]() |
![]() |
![]() |
#13 | |
VIP Member
Join Date: Dec 2001
Location: phoenix
Posts: 1,486
Likes: 66
Liked 704 Times in 281 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#14 |
Banned
Join Date: Dec 2001
Posts: 147
Likes: 0
Liked 5 Times in 3 Posts
|
![]()
Listen to Dwight's advice, the bhj fixtures are about as bad as just leaving the block alone, we have a CNC mill at my shop that we do this job on, can't beat a CNC machine when it comes to exacting tolerances. We only charge $450 though and seeing that others are charging $500-700 to do it on a manual mill I might need to go up on pricing...lol
|
![]() |
![]() |
![]() |
#15 | |
VIP Member
Join Date: Oct 2008
Location: Somerset,Ky
Posts: 1,370
Likes: 351
Liked 303 Times in 102 Posts
|
![]() Quote:
Allen, Ten years ago when I did lifter bores w/BHJ we got $375.00 SBC $425.00 BBC including bushings, by time took and bushings was how we come up with those numbers,CNC you can walk away some,manual machine pretty much stuck there. Mike Taylor 3601 |
|
![]() |
![]() |
![]() |
#16 |
Member
Join Date: Jun 2010
Location: VA
Posts: 230
Likes: 23
Liked 21 Times in 13 Posts
|
![]()
Allen, Without the fixture, what do you use for a reference, and how do you choose the angle ? thanks
__________________
Brian Carpenter Stock 1358 |
![]() |
![]() |
![]() |
#17 |
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,999
Likes: 64
Liked 773 Times in 192 Posts
|
![]()
Factory blueprints and a CNC is the best.
__________________
![]() |
![]() |
![]() |
![]() |
#18 |
Banned
Join Date: Dec 2001
Posts: 147
Likes: 0
Liked 5 Times in 3 Posts
|
![]()
Sorry I'm slow responding, I don't usually get on here while I'm at the shop, but Dwight answered the question already, we have factory blueprint locations programmed into the CNC, and if needed we just make program changes if an angle or location change is required...
|
![]() |
![]() |
![]() |
#19 | |
Member
Join Date: Jun 2010
Location: VA
Posts: 230
Likes: 23
Liked 21 Times in 13 Posts
|
![]()
Thanks guys. Looking at some dated drawings, w/o dimensions no less, The BBM lifter looks to be 90 degrees to the deck, so at least for this block using the crank and cam centerline to swing the angle, then line up with cam centerline should work. I do dimensional inspection work for a living, so I enjoy understanding how this stuff is done.
Quote:
__________________
Brian Carpenter Stock 1358 |
|
![]() |
![]() |
![]() |
#20 | |
Member
Join Date: Feb 2007
Location: NORTHEAST
Posts: 287
Likes: 1
Liked 18 Times in 10 Posts
|
![]() Quote:
I do all my blocks in a HAAS CNC machine and we only charge 275.00 for machining lifter bores LOL. I guess I will have to go up. |
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|