|
|
06-11-2024, 07:07 AM | #1 |
Member
Join Date: Feb 2007
Posts: 138
Likes: 95
Liked 4 Times in 4 Posts
|
LS/SBC parts - Wheels, Converters, misc
Weld Alumastar 15 x 12 rear wheels with 4.75 pattern and 3” BS. $800.00. Very good condition, no screw holes
Precision Performance Products Kwik shift I manual shifter – excellent condition – no mounting plates. Black. 3 speed, push to shift with clean neutral. $350.00 TCI SBC/BBC lightweight 29.2 168T flexplate PN 399870LW, like new. Weighs 6.09lbs. Can barely see the contact patch on the starter ring. Original date was 1/19, but was only ran in the car for 2 races. Will need recertified. Excellent condition $300.00 Jesel Dogbone lifters LFD-44002 .842 Diameter – set of 16 – $800.00 LS Bryant crankshaft – 4” stroke – 58x - $2800 Carillo rods 6.1 rods (was used with Bryant crankshaft above) BE :2.2253 PE :0.9285 Length: 6.100 B Width : 0.938 $1200.00 Forged small journal 327 GM crankshaft. Offset ground (.020 under) by Shaftech. 1.979 rods, 2.300 mains – 3.263 stroke $750.00 Oliver I beam 5.7 rods set of 8 (was used with Shaftech crank above) BE: 2.125 PE: 928 Length: 5.7 Weight each: 575 Grams $800.00 8” ATI converter - Flashed 6500 behind 427/430 LS Combo –Powerglide spline - $500 7" Converter - Dynamic. Powerglide input, flashed 7000 behind 327/275 hp combo. - $500.00 Wilson 1” 4 hole aluminum tapered spacer – Dominator flange PN 024110 - $150 used for test only 6.00 12 bolt ring and pinion. Ring gear has been backcut - less than 10 runs $250.00 Polished fabricated valve covers with baffles tall - $100.00 Manley 221443P-16 valve springs with 23648-16 Ti - retainers, locks and 42573-16 locators (run on dyno) $300 for set. ATI balancer pulley PN 916794 4 groove aluminum 6.430 diameter - New $40.00 ATI balancer pulley PN 916732 4 groove aluminum 6.430 diameter – used $50.00 CV products 3/8 pushrods (qty 18) 9.200 x .080 x 5/16 ends – used but good condition – $30.00 Trend 3/8 pushrods (qty 16) 7.450 x .135 x 5/16 ends – used but good condition) $50 Trend 7/16 tapered pushrods (qty 16) 9.400 x .165 x 5/16 ends new - $150 Trend 3/8 pushrods (qty 8) 9.400 x .135 x 5/16 ends used - $25 Trend 3/8 pushrods (qty 8) 9.450 x .135 x 5/16 ends used - $25 Trend (qty 17) – 9.150 DBL taper .135 wall pushrods 5/16 ends (used good) $35 Trend 9.400 DBL taper .135 wall pushrods 5/16 ends (11) new $150 Trend 9.300 DBL taper .135 wall pushrods 5/16 ends (11) new $150 JRI 2010-2015 Camaro front struts $500.00 used. 1 – Lingenfelter billet steel LS block girdle, No hardware $500 2 GM truck oil pans (1999-2006) pan only $50.00 each Pit Pal Pit Ramps 280 with vertical storage pouch for trailer Aluminum, 24.00 in. Length, 8.00 in. Width, 2.75 in. Height, Pair with pouch $200 Jerry Bickel Pit ramps and trailer pouch $120.00 Can bring to Norwalk National event 260-223-0157 superstock@live.com
__________________
Jeff Myers SS3254 S1522 Last edited by JeffM; 06-21-2024 at 07:01 AM. |
06-13-2024, 07:54 AM | #2 |
Member
Join Date: Sep 2012
Location: Deployed
Posts: 106
Likes: 38
Liked 314 Times in 52 Posts
|
Re: LS/SBC parts - Wheels, Converters, misc
Hi Jeff, is the shifter for a TH 350? FWD or Reverse valve body? Thanks!
__________________
Brian Zenzen SS 5404 STK 5401 |
06-13-2024, 08:00 AM | #3 | |
Member
Join Date: Feb 2007
Posts: 138
Likes: 95
Liked 4 Times in 4 Posts
|
Re: LS/SBC parts - Wheels, Converters, misc
Quote:
Any 3 speed transmission with clean neutral all the way forward. Push to shift. Park is all the way in the rear P, R,1,2,3,N. Cable exits in the rear.
__________________
Jeff Myers SS3254 S1522 |
|
06-30-2024, 01:42 PM | #4 |
Junior Member
Join Date: Oct 2003
Location: Lumberton N.C.
Posts: 96
Likes: 3
Liked 40 Times in 14 Posts
|
Re: LS/SBC parts - Wheels, Converters, misc
Jeff sent you a text about the shifter and LS ATI converter
__________________
Phillips auto body Custom paint Lumberton, NC 910-739-7171 |
|
|