Slotting stock rockers

Michigan Skip · 06-21-2009, 07:58 AM

I need to open up the slot on a set of sbc rockers to fit 7/16 rocker studs. I have access to a mill at work but wondered how to set the rocker up in the vise.
TIA
Skip

Kegracing · 06-21-2009, 08:10 AM

Skip,
I cut a set a few years ago, and had same questions and issues. I ended up making a metal bracket that held them down, as I did not want to clamp the rocker itself. Sorry, I do not have the bracket anymore or would send a picture.

However you do them, keep plenty of fluid running on the cutter, to help keep heat down.

Good luck.

Ken

Alan Roehrich · 06-21-2009, 08:40 AM

There are several outlets for the 7/16" small block rockers, even though I have a mill, I'm not sure I'd bother with trying to open a set of 3/8" rockers up to fit.

I would certainly not clamp them in a vise, as you will likely not be able to hold them securely enough. I think I'd take a piece of flat stock and mill slots in it to set the rockers in, and then clamp the flat stock and the rocker to the mill table. You need to put something between the clamp and the rocker to prevent the clamp from scoring the rocker, as the scoring will create stress risers.

Ken is correct, any heat generated by cutting the rockers will ruin the heat treat, it must be carried off by coolant. Are you going to have to drill the rocker balls as well?

Terry Cain · 06-21-2009, 08:46 AM

Find a shop in your area or someone who works at a shop that has a wire EDM machine. No stress and cuts like butter.

Michigan Skip · 06-21-2009, 09:26 AM

Thanks guys for the advice.

Kenny Wigington · 06-21-2009, 12:00 PM

Skip, look here-http://competitionproducts.com/prodinfo.asp?number=6151

Buy 2 sets and have spares. They are pretty tough !

06-21-2009, 07:58 AM	#1
Michigan Skip Junior Member Join Date: Aug 2002 Location: Three Oaks MI Posts: 58 Likes: 0 Liked 0 Times in 0 Posts	Slotting stock rockers I need to open up the slot on a set of sbc rockers to fit 7/16 rocker studs. I have access to a mill at work but wondered how to set the rocker up in the vise. TIA Skip __________________ Skip Willis 95 Z28 IHRA ST/666

06-21-2009, 08:10 AM	#2
Kegracing Member Join Date: Jun 2002 Location: Red Oak, TX Posts: 441 Likes: 0 Liked 0 Times in 0 Posts	Re: Slotting stock rockers Skip, I cut a set a few years ago, and had same questions and issues. I ended up making a metal bracket that held them down, as I did not want to clamp the rocker itself. Sorry, I do not have the bracket anymore or would send a picture. However you do them, keep plenty of fluid running on the cutter, to help keep heat down. Good luck. Ken

06-21-2009, 08:40 AM	#3
Alan Roehrich Veteran Member Join Date: May 2006 Location: Murfreesboro TN Posts: 5,105 Likes: 1,564 Liked 1,789 Times in 408 Posts	Re: Slotting stock rockers There are several outlets for the 7/16" small block rockers, even though I have a mill, I'm not sure I'd bother with trying to open a set of 3/8" rockers up to fit. I would certainly not clamp them in a vise, as you will likely not be able to hold them securely enough. I think I'd take a piece of flat stock and mill slots in it to set the rockers in, and then clamp the flat stock and the rocker to the mill table. You need to put something between the clamp and the rocker to prevent the clamp from scoring the rocker, as the scoring will create stress risers. Ken is correct, any heat generated by cutting the rockers will ruin the heat treat, it must be carried off by coolant. Are you going to have to drill the rocker balls as well? __________________ Alan Roehrich 212A G/S

06-21-2009, 08:46 AM	#4
Terry Cain Senior Member Join Date: Feb 2008 Location: Georgetown, Indiana (close to Louisville, KY) Posts: 776 Likes: 530 Liked 230 Times in 106 Posts	Re: Slotting stock rockers Find a shop in your area or someone who works at a shop that has a wire EDM machine. No stress and cuts like butter. __________________ Terry Cain ???? STK tcain19689585@gmail.com

06-21-2009, 09:26 AM	#5
Michigan Skip Junior Member Join Date: Aug 2002 Location: Three Oaks MI Posts: 58 Likes: 0 Liked 0 Times in 0 Posts	Re: Slotting stock rockers Thanks guys for the advice. __________________ Skip Willis 95 Z28 IHRA ST/666

06-21-2009, 12:00 PM	#6
Kenny Wigington Senior Member Join Date: Sep 2004 Location: Cumming,Ga. USA Posts: 967 Likes: 36 Liked 60 Times in 12 Posts	Re: Slotting stock rockers Skip, look here-http://competitionproducts.com/prodinfo.asp?number=6151 Buy 2 sets and have spares. They are pretty tough ! __________________ 2894 STK