|
|
07-26-2023, 08:23 PM | #1 |
Senior Member
Join Date: Feb 2008
Location: Georgetown, Indiana (close to Louisville, KY)
Posts: 771
Likes: 514
Liked 225 Times in 104 Posts
|
Flat tappet lifter failure
Curious how many have had this problem regardless of reasoning in last 5 years or so.
Last edited by Terry Cain; 07-27-2023 at 06:49 PM. |
07-27-2023, 01:18 AM | #2 |
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,597
Likes: 2,376
Liked 2,126 Times in 612 Posts
|
Re: Flat tappet lifter failure
My boy has had issues that have cost engines while
running the expensive billet stuff.
__________________
John Irving 741 Stock 741 Super Stock |
07-27-2023, 09:34 AM | #3 |
Senior Member
Join Date: Sep 2007
Location: Henderson, NV
Posts: 578
Likes: 7
Liked 47 Times in 25 Posts
|
Re: Flat tappet lifter failure
Spring pressure and lifter diameter are factors as well. Stock lifters are good at 380 lb. open and .921" diameter. 500-550 lb. open are another story.
|
Liked |
07-27-2023, 08:51 PM | #4 |
Member
Join Date: Dec 2018
Location: Massachusetts
Posts: 168
Likes: 189
Liked 237 Times in 89 Posts
|
Re: Flat tappet lifter failure
I lost one cam lobe, I noticed it after about 100 runs. I’m not sure when it went away. Most likely caused by lack of oiling at low rpm. From what I’ve been told the tool steel lifter, cast cam combination is only good for maybe 200 runs if you’re lucky. Go fast stuff can be a P.I.T.A.
__________________
George Mirza D/SA 1236 ‘71 Duster 340 Last edited by Gmirza; 07-28-2023 at 07:47 PM. |
07-27-2023, 09:30 PM | #5 | |
Senior Member
Join Date: Dec 2001
Location: Elysburg, Pa
Posts: 703
Likes: 306
Liked 247 Times in 95 Posts
|
Re: Flat tappet lifter failure
Quote:
|
|
07-28-2023, 07:46 PM | #6 | |
Member
Join Date: Dec 2018
Location: Massachusetts
Posts: 168
Likes: 189
Liked 237 Times in 89 Posts
|
Re: Flat tappet lifter failure
Quote:
I’m not sure. I didn’t check them.
__________________
George Mirza D/SA 1236 ‘71 Duster 340 Last edited by Gmirza; 07-28-2023 at 07:51 PM. |
|
07-28-2023, 04:06 PM | #7 | |
Junior Member
Join Date: Jan 2018
Location: Colorado
Posts: 85
Likes: 235
Liked 101 Times in 26 Posts
|
Re: Flat tappet lifter failure
Quote:
|
|
10-14-2023, 09:48 AM | #8 |
Senior Member
Join Date: Apr 2020
Location: Phila, PA
Posts: 686
Likes: 0
Liked 602 Times in 328 Posts
|
Re: Flat tappet lifter failure
|
10-14-2023, 11:09 AM | #9 |
Junior Member
Join Date: Nov 2001
Location: Brentwood, California
Posts: 73
Likes: 214
Liked 192 Times in 37 Posts
|
Re: Flat tappet lifter failure
It appears that some on this site may be in the wrong class or running the wrong combination. To those, please pick something that fits your personal agenda and leave the silent majority alone.
Thank you, Jim Grossi |
10-14-2023, 12:04 PM | #10 |
VIP Member
Join Date: May 2006
Location: Murfreesboro TN
Posts: 4,969
Likes: 1,136
Liked 1,218 Times in 313 Posts
|
Re: Flat tappet lifter failure
I'm hearing the rule change is "out of the question", which is a great thing.
Was in the shop with a legend yesterday, he's raced as long as I have lived. All he said was "them boys will keep on and they'll be in Super Stock soon." The lifter change is NOT a solution. It won't prevent failures. Roller lifters fail, too. And it is just as catastrophic. It would require an entirely new lobe design, you don't just stick roller lifters in on the cam you have. Flat tappets can actually accelerate FASTER at a certain point. But then the roller comes into its own. If you change to roller lifters, you need different springs, and different pushrods. The stud mount rocker cars will snap rocker studs like twigs. The cars allowed 0.875" and 0.904" lifters will have access to better lobe profiles, and have fewer roller lifter failures.The stud mount rocker cars will also rip the rocker stud bosses out of the heads. Current valve spring technology will allow the use of lobes that will extend the RPM range, by 1,000 RPM. The introduction of roller lifters will simply begin series of escalations that will take 3-5 years to develop, and cost thousands upon thousands of dollars. It will alter the factoring drastically. If anyone ever lets that genie out of the bottle, the class will be wrecked for years.
__________________
Alan Roehrich 212A G/S |
Liked |
|
|