|
![]() |
#1 |
Senior Member
Join Date: Dec 2001
Location: wv
Posts: 882
Likes: 42
Liked 56 Times in 21 Posts
|
![]()
Gen. Is showing. A code 3
Will not turn over We are on the road
__________________
Vic Guilmino 1129 STK |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Aug 2007
Location: California, Ky
Posts: 667
Likes: 30
Liked 1 Time in 1 Post
|
![]()
What is "Gen." specifically? Give me as much info about whatever it is and I'll see what I can find.
__________________
Kris Rachford 69 Cobra 428CJ 4 Speed C/S 3032 |
![]() |
![]() |
![]() |
#3 |
VIP Member
Join Date: Mar 2010
Location: Newport News, VA
Posts: 1,438
Likes: 372
Liked 129 Times in 59 Posts
|
![]()
Vic,
Is this the generator in the coach? What make and model is the unit? Lew
__________________
Lew Silverman #2070 "The Wagon Master" N/SA |
![]() |
![]() |
![]() |
#4 |
VIP Member
Join Date: Dec 2001
Location: Richmond Hill, Georgia
Posts: 2,003
Likes: 0
Liked 1 Time in 1 Post
|
![]()
Try disconecting the power source for a couple of minutes. This might reset the codes.
__________________
Art Leong 2095 SS |
![]() |
![]() |
![]() |
#5 |
VIP Member
Join Date: Mar 2010
Location: Newport News, VA
Posts: 1,438
Likes: 372
Liked 129 Times in 59 Posts
|
![]()
If it's an Onan -
SERVICE CHECK FAULT—CODE NO. 3(A second-level fault occurred) Corrective Action: Check the second-level fault code by touching Stop. See what the second-level fault is. Lew
__________________
Lew Silverman #2070 "The Wagon Master" N/SA |
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Aug 2007
Location: California, Ky
Posts: 667
Likes: 30
Liked 1 Time in 1 Post
|
![]()
Could it be low on oil? Or not sitting level to where it thinks it low on oil?
__________________
Kris Rachford 69 Cobra 428CJ 4 Speed C/S 3032 |
![]() |
![]() |
![]() |
#7 |
VIP Member
Join Date: Jan 2003
Location: Allentown,PA
Posts: 2,439
Likes: 788
Liked 704 Times in 207 Posts
|
![]()
Vic,you must press and hold the switch on the generator to get the complete code.
The 3 or 33 code just tells you there are other codes present Matt Schurman just repaired my Onan for the same problem ,it would run fine and then after being shut off it would not crank over to restart. Had a code pertaining to the governer,altho it actually was a problem with the inverter section which is pretty much the brain of the generator.
__________________
Tom Goldman 1500 SG , 1506 STK |
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Dec 2001
Location: wv
Posts: 882
Likes: 42
Liked 56 Times in 21 Posts
|
![]()
Oil is good
It is ever a 3 or 33
__________________
Vic Guilmino 1129 STK |
![]() |
![]() |
![]() |
#9 |
VIP Member
Join Date: Mar 2010
Location: Newport News, VA
Posts: 1,438
Likes: 372
Liked 129 Times in 59 Posts
|
![]()
Tom is right. Hold the STOP button to get the secondary-fault code -
Here's a link to what you may find - http://www.alpinesocal.com/sitebuild...leshooting.pdf Keep us posted! Lew
__________________
Lew Silverman #2070 "The Wagon Master" N/SA |
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Dec 2001
Location: wv
Posts: 882
Likes: 42
Liked 56 Times in 21 Posts
|
![]()
When I hold the shop button the light stays on
__________________
Vic Guilmino 1129 STK |
![]() |
![]() |
![]() |
|
|