|
![]() |
#11 |
Member
Join Date: Nov 2016
Location: Indianola Washington
Posts: 367
Likes: 0
Liked 411 Times in 132 Posts
|
![]()
There should be a micro switch that PPP can supply that mounts opposite side of the Netural safety switch. It's triggered by the same rod. No external bracket and switch required then . Very clean and they provide a screw on connector wiring harness same as the Safety switch hasness .
|
![]() |
![]() |
Liked |
![]() |
#12 |
Member
Join Date: Sep 2008
Posts: 128
Likes: 2
Liked 99 Times in 32 Posts
|
![]()
Just curious how much brake pressure do you use at the starting line? I have seen a lot of data and have never seen brake pressure over 4-500 psi (on 160 mph plus cars). I would think anymore than that would lock em up bad at the stripe.....
|
![]() |
![]() |
![]() |
#13 |
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,577
Likes: 2,307
Liked 2,107 Times in 602 Posts
|
![]()
Set @ 800 and release @ 200 generally on our stuff.
120/125 MPH Stockers.
__________________
John Irving 741 Stock 741 Super Stock |
![]() |
![]() |
Liked |
![]() |
#14 |
Senior Member
Join Date: Dec 2003
Location: Vacaville Ca
Posts: 803
Likes: 766
Liked 626 Times in 266 Posts
|
![]()
__________________
Barry Polley 758 A/SA California- No place to race! |
![]() |
![]() |
Liked |
![]() |
#15 |
VIP Member
Join Date: Jun 2007
Location: Northern New Jersey suburbs
Posts: 2,298
Likes: 25
Liked 531 Times in 208 Posts
|
![]()
Anyone hook up this setup using a Turbo Action Cheetah with a reverse pattern 3 speed trans ?
I'd like to try it and making a switch to only work in low gear looks like a challenge.....
__________________
Rich Biebel S/C 1479 Stock 147R |
![]() |
![]() |
![]() |
#16 |
Junior Member
Join Date: Aug 2012
Location: Richland, WA
Posts: 69
Likes: 384
Liked 62 Times in 17 Posts
|
![]()
I haven't done it with a reverse pattern but I think it could be done fairly easily by mounting a momentary, lever micro switch on a bracket attached at the trans pan rail or in tandem with the shift cable bracket. Switches like these are available in short or long arm for less than $20. Should be able to activate when the shift lever arm is in low gear only.
__________________
Mike Merk |
![]() |
![]() |
![]() |
#17 |
Member
Join Date: Jun 2010
Location: VA
Posts: 230
Likes: 23
Liked 21 Times in 13 Posts
|
![]()
Easy to do. I use a neutral start switch I got from turbo action.
__________________
Brian Carpenter Stock 1358 |
![]() |
![]() |
![]() |
#18 | |
VIP Member
Join Date: Jun 2007
Location: Northern New Jersey suburbs
Posts: 2,298
Likes: 25
Liked 531 Times in 208 Posts
|
![]() Quote:
I'm an old pure foot breaker but always open to trying something different. When I owned this car in 2006 I did install a 2 step button switch and low rpm adjustable chip but never used it. It was not comfortable to me leaning hard on the brake pedal and using that hand operated button. Using the brake pedal with a pressure switch sounds more appealing I have taken the shifter apart at least 4 times to do various things.....one more time can't hurt....
__________________
Rich Biebel S/C 1479 Stock 147R Last edited by Rich Biebel; Today at 12:18 PM. |
|
![]() |
![]() |
![]() |
#19 | |
VIP Member
Join Date: Jun 2007
Location: Northern New Jersey suburbs
Posts: 2,298
Likes: 25
Liked 531 Times in 208 Posts
|
![]() Quote:
I've made switches like that on other cars but the shift pattern was forward. I'm sure it can be done but it takes some thought and fabrication The built in neutral start switch posted above is a good solution
__________________
Rich Biebel S/C 1479 Stock 147R Last edited by Rich Biebel; Today at 12:19 PM. |
|
![]() |
![]() |
![]() |
|
|