Re: FS/H CobraJet Body In White Project
 

http://9500rpm.com/GWCJ/gwcj082.jpg
Tail lights, rocker panels, weather stripping all installed.

http://9500rpm.com/GWCJ/gwcj083.jpg
Door glass installed. Door harness installed and power windows tested.

http://9500rpm.com/GWCJ/gwcj084.jpg
Seats located and bolted in temporarily. Main wiring harness tested and installed. Big Stuff ECU and electrical components mounted on plate attached to roll cage.

http://9500rpm.com/GWCJ/gwcj085.jpg
Headlights installed. Gas cylinders installed. No need for a prop rod to hold up the hood.

http://9500rpm.com/GWCJ/gwcj086.jpg
Deck lid and rear bumper beam installed.

Re: FS/H CobraJet Body In White Project
 

Very nice!

Re: FS/H CobraJet Body In White Project
 

Looking very nice and the Mule looks great also...

Re: FS/H CobraJet Body In White Project
 

Wow, George the car looks great! and also congrats for the Mule being #2 qualifier at Norwalk. You two guys are awesome. Can't wait to see this one done!

Re: FS/H CobraJet Body In White Project
 

Latest updates between racing at Norwalk and yesterdays S/SS combo at Milan.

http://9500rpm.com/GWCJ/gwcj087.jpg
K-member ready to bolt up.

http://9500rpm.com/GWCJ/gwcj088.jpg
K-member bolted into body. Clutch linkage also bolted in place. Brad Zaskowski built 5 sets of clutch linkage for the stick shift CobraJets we have assembled. Good design and nice workmanship.

http://9500rpm.com/GWCJ/gwcj089.jpg
Upper 3 link bar and mounting bracket bolted into body.

http://9500rpm.com/GWCJ/gwcj090.jpg
Rear firewall mocked up with Clecos.

http://9500rpm.com/GWCJ/gwcj093.jpg
Rear firewall rivited in.

Re: FS/H CobraJet Body In White Project
 

Looks great.

Re: FS/H CobraJet Body In White Project
 

More progress on the CJ.

http://9500rpm.com/GWCJ/gwcj094.jpg
Clutch, brake and gas pedals bolted in. The drive by wire gas pedal was replaced with a fox body gas pedal since I will be using a BigStuff ECU.

http://9500rpm.com/GWCJ/gwcj095.jpg
Master cylinder installed.

http://9500rpm.com/GWCJ/gwcj097.jpg
Aeromotive fuel cell installed. Dash 8 hoses being cut and assembled.

http://9500rpm.com/GWCJ/gwcj098.jpg
Rear brakes assembled.

http://9500rpm.com/GWCJ/gwcj101.jpg
Moched up with wheels and tires.

http://9500rpm.com/GWCJ/gwcj103.jpg
Fuel lines installed on the body.

Re: FS/H CobraJet Body In White Project
 

Very nice build good luck.

Re: FS/H CobraJet Body In White Project
 

Getting closer. Lots of little details to finish up. Here some more pictures.

http://9500rpm.com/GWCJ/gwcj105.jpg
Fitting the BigStuff EFI harness to the engine.

http://9500rpm.com/GWCJ/gwcj106.jpg
Dashboard bolted in and tach mounted.

http://9500rpm.com/GWCJ/gwcj107.jpg
9 inch wide Hoosier tires mounted on CobraJet wheels.

http://9500rpm.com/GWCJ/gwcj108.jpg
I modified the Moroso inline radiator cap so I could pickup up temperature for the BigStuff ECU and the electric water temp gauge. The Coyote cylinder heads don't really have any threaded holes or even any good places to drill and tap a threaded hole to mount a temperature sensor.

http://9500rpm.com/GWCJ/gwcj109.jpg
I bent and fit two panels to cover and flatten out the back seat area to make it easier to lay a piece of carpet back there.

http://9500rpm.com/GWCJ/gwcj110.jpg
American Racing Headers moched up on engine. The Lakewood bellhousing is only temporary. I will be using a Browell bellhousing.

http://9500rpm.com/GWCJ/gwcj111.jpg
Engine set in car for moch up purposes. I will most likely come back out in a few days after I fit the fuel lines from the rails to the regulator and a few other items.

http://9500rpm.com/GWCJ/gwcj112.jpg
Engine moched up in car.

http://9500rpm.com/GWCJ/gwcj113.jpg
Engine and drivers side header moched up in car.

Re: FS/H CobraJet Body In White Project
 

Awesome